Small Group Tutorials

Here to help students catch up, keep up, and move ahead. Book a consultation here.

How to Perform in the new G3 SEC Examinations | Learner’s Guide Vol 1403 | Physics Sports-Day Scoreboard Circuits — Series, Parallel, Resistance and Fault Diagnosis

G3 SEC Physics learners preparing for 2027 can use a fictional sports-day scoreboard fault to learn circuit structure, resistance, current, potential difference, data-based diagnosis and practical evaluation. This guide moves from definitions to worked examples and then to examination-style reasoning. It is a study resource for Singapore secondary students and parents, not a description of an actual scoreboard or a repair manual.

The official 2027 G3 Physics syllabus code is K323, with d.c. circuits and practical investigations among its learning outcomes. This volume follows the sports-day evidence work of Volumes 1399–1402; it extends the same habit of checking evidence into electricity. Every measurement below is an invented classroom number. Keep all actual practical work under your school teacher’s directions with appropriate low-voltage apparatus.

Quick learning route: start with charge and current; define voltage and resistance; read circuit diagrams; solve series and parallel networks; understand sensors and potential dividers; interpret graphs; evaluate anomalous readings; investigate hypothetical faults; answer scaffolded exercises; and finish with a short mini-mock.

1. A new investigation after the Sports Day results audit

A sports-day timing result has been checked, but a fictional portable scoreboard stops displaying one digit after a test run. This chapter turns that incident into a G3 Physics learning problem. The aim is not to repair real electrical equipment. It is to learn how to model a circuit, calculate expected readings, compare a model with observations, and say what the evidence actually supports. Every circuit, voltage, current, cost and person in the classroom story is invented. Students should use diagrams, a school-approved low-voltage educational circuit or supplied data, never a household socket or an opened appliance. The practical habits are still useful: identify a quantity, state its unit, decide where an instrument belongs, and look for contradictions before selecting an explanation.

2. Know where the qualification fits

The Singapore-Cambridge Secondary Education Certificate begins in 2027. The official G3 Physics syllabus is K323. Its scheme lists Paper 1 multiple choice, one hour, 40 marks and 30%; Paper 2 structured and free response, one hour 45 minutes, 80 marks and 50%; and Paper 3 practical, one hour 50 minutes, 40 marks and 20%. The theory papers assess knowledge and application, while the practical work demands planning, careful observation and evaluation. This guide is original revision, not a specimen paper. English Language K300 and Mathematics K310 remain separate examinations. The wider English–Mathematics–Science route is an optional study method, not a combined SEC assessment. Confirm the latest syllabus and school instructions before planning a revision schedule.

3. Begin with current rather than a component name

Electric current is the rate of flow of electric charge. In a simple d.c. model, I = Q/t: a charge of 6 coulombs passing a point in 3 seconds corresponds to a current of 2 amperes. The numbers describe charge passing a point, not charge being used up inside the lamp. A common error says that current must be smaller after a bulb because the bulb consumes electricity. Energy is transferred by the component, while charge is conserved in the circuit. To make an explanation clear, distinguish what flows, what drives it, and what is transferred. When current is zero, a stopped display alone cannot reveal whether the battery, a switch or a wire caused the interruption.

4. Distinguish e.m.f., potential difference and resistance

The e.m.f. of a source represents energy supplied per unit charge; potential difference across a component represents energy transferred per unit charge. Both use volts, but their definitions serve different places in the model. Resistance is potential difference divided by current, R = V/I, with ohms as the unit. For a resistor with 6.0 V across it and 0.30 A through it, the resistance is 20 ohms. Do not write 0.05 ohms by reversing the division. Writing the known quantity above its unit helps: volts divided by amperes gives ohms. The equation alone cannot diagnose a damaged connection unless we also know where the voltage and current were measured.

5. A readable circuit diagram is a scientific argument

A circuit diagram does more than decorate an answer. It tells a reader which components share a path, which components have separate branches, and where a test instrument is connected. Use the prescribed symbols for source, switch, lamp, resistor, ammeter and voltmeter. Place an ammeter in series with the element whose current it measures; place a voltmeter across the element whose potential difference it measures. A diagram that puts an ammeter directly across a power source suggests an inappropriate connection and may be dangerous in a real circuit. For the exercise, sketch before calculating and mark the direction of conventional current consistently. Labels such as A, B and C prevent confusion when there are two lamps.

6. Series circuits have a single current path

In a series arrangement there is one route for the circuit current. The same current passes through each component, the potential differences across components add to the source potential difference, and resistances add for ideal resistors. With 4.0 and 8.0 ohms in series across an ideal 12 V source, the total resistance is 12 ohms and the current is 1.0 A. The respective potential differences are 4.0 V and 8.0 V. A learner who gives each resistor 12 V has treated a series circuit as parallel. The quick test is to add the component voltages: 4 + 8 = 12 V. This accounting check is often faster than repeating the calculation.

7. Parallel circuits share potential difference

A parallel arrangement gives current more than one route. Across each ideal branch the potential difference is the same as across the source; branch currents add to give the source current. A 6.0-ohm branch and a 3.0-ohm branch across an ideal 6.0 V source carry 1.0 A and 2.0 A respectively, so the source supplies 3.0 A. Their effective resistance is 2.0 ohms, obtained from 1/R = 1/6 + 1/3. The answer is below the smallest individual branch resistance. That is a useful reasonableness test. It would be incorrect to add 6 and 3 directly as though the resistors were in series.

8. Reading a fault is not the same as guessing a fault

Suppose one display segment fails while another remains lit. That observation is consistent with more than one mechanism depending on the circuit arrangement. It might indicate an open branch, a failed segment or a loose local connection in a parallel design. It does not prove that the source has failed. In a series design, an open circuit anywhere on the only path could stop every element. Before diagnosing, state the assumed wiring and the observations needed to distinguish rival possibilities. A strong G3 response might say, “A broken branch is possible; measure the potential difference across the branch and compare its current with the other branch.” Careful conditional language is a strength, not hesitation.

9. A meter reading needs a location

A table headed only “current: 0.2 A” is incomplete for a network with branches. The location matters. A total-source reading of 0.20 A can coexist with branch readings of 0.12 A and 0.08 A, while a claim that all three are 0.20 A would need a different topology. Label every column with measured quantity, unit and point of measurement. For example, I_source/A, I_branch1/A, V_resistor/V. For the 0.12 A and 0.08 A branches, check 0.12 + 0.08 = 0.20 A. If the measured sum differs more than the reasonable uncertainty, investigate the method or assumption rather than silently adjusting the data.

10. Use voltage-divider reasoning carefully

Two ideal fixed resistors in series form a potential divider. With a 9.0 V supply, 1.0 kilo-ohm above a 2.0 kilo-ohm resistor, and output measured across the 2.0 kilo-ohm resistor, V_out = 9 × 2/(1 + 2) = 6.0 V. The corresponding current is 3.0 mA. If the output is instead measured across the 1.0 kilo-ohm resistor, it is 3.0 V. This illustrates why the point of measurement is part of the answer. A variable divider changes the relative resistance and hence the output potential difference. A practical device connected to the output can affect the ideal calculation; the simple classroom model assumes no significant loading unless data say otherwise.

11. Sensors change how a circuit responds

The K323 syllabus includes light-dependent resistors and negative-temperature-coefficient thermistors as input transducers in potential dividers. For a typical light-dependent resistor, resistance falls as light intensity increases. For an NTC thermistor, resistance falls as temperature increases. But whether the output voltage rises or falls depends on the position of the changing component and where the output is taken. Students sometimes memorise “more light means more voltage” without drawing the divider; that statement is not universally correct. Always sketch which resistor is above and which below the output point. Trace the changed resistance, total current and voltage share. Then predict the effect on a reading. This is more reliable than memorising a direction detached from a circuit.

12. Separate a resistor from a lamp or diode

Not every component has a constant resistance. The K323 syllabus expects interpretation of current–voltage characteristics for an ohmic metallic conductor at constant temperature, a filament lamp and a semiconductor diode. For an ohmic conductor, a graph of current against potential difference is a straight line through the origin when conditions remain constant; the gradient depends on the axis arrangement. A filament lamp heats as current rises, changing its resistance. A diode conducts readily chiefly in one direction when appropriately biased. Treating every display component as a fixed resistor can therefore be a useful first model but not a complete account of a real LED display. When the question supplies a simplified component model, identify its limits rather than importing unprovided electronics specifications.

13. Power and energy must not be confused

Electrical power is the rate of energy transfer: P = VI. If a fictional module operates at 5.0 V and draws 0.40 A, its power in the simple model is 2.0 W. If it runs for 120 seconds at that rate, energy transferred is 240 J. Do not report 240 W or 2.0 J because the numerical answers happen to look tidy. Power is a rate; energy accumulates with time. A school cost calculation may convert watts to kilowatts and hours to find kWh, but this exercise does not certify battery runtime or electrical safety. Real hardware has tolerances and other losses beyond the simplified model. The student’s task is to make the assumptions visible and the units consistent.

14. A fair experiment changes one planned factor

Suppose a teacher supplies a safe, school-approved low-voltage circuit and asks how the current through an ohmic resistor varies as potential difference changes. The independent variable is the potential difference chosen for each reading. The dependent variable is the current measured. Important controls include resistor identity and temperature within reasonable stability. Record the readings in a table, repeat sensible points where possible, and identify an anomalous value rather than deleting it without reason. Before starting, discuss safe supervision and the equipment’s rating. Draw a labelled circuit with the ammeter in series and the voltmeter across the resistor. The conclusion should refer to the pattern in the data, the precision of the instruments and any limitation that might change the relationship.

15. Graph interpretation is more than a ruler exercise

On a current–potential-difference graph, a straight line through the origin can support proportionality for the tested range. It does not prove that every value outside the measured range behaves the same way. The gradient is I/V if I is on the vertical axis and V on the horizontal axis, so its reciprocal corresponds to resistance for an ohmic resistor. Reverse the axes and the meaning of the gradient changes. Mark units on axes, choose scales that use the space well, plot small crosses, and use an appropriate line of best fit rather than a zigzag through every point. For a gradient, select widely spaced points on the fitted line, not necessarily two original readings.

16. Explain uncertainty without inventing precision

A digital reading of 0.21 A does not mean the circuit current is known to infinitely many decimal places. An analogue instrument has a scale, and a digital instrument has a resolution and possibly additional error. Never attach a more precise claim than the measurements warrant. If one current reading is 0.20 A and another is 0.21 A, it is premature to declare a meaningful change without considering the apparatus, repetition and stated accuracy. An outlier might result from a loose lead, a reading error or a genuine variation. Good evaluation names plausible causes and tests them. “Human error” on its own is too vague. Describe what could have happened and how a better procedure would reduce that possibility.

17. Plan a fault-finding sequence rather than random reconnection

The hypothetical scoreboard has three checkpoints: source, main switch and display branches. Start with a visual inspection of the supplied diagram and the recorded observations; do not manipulate live equipment outside authorised school practical work. Test a single prediction at each stage. If a source voltage is present but a branch draws no current, distinguish an open branch from a connection error using additional allowed readings. If a switch is open, current should not pass through that ideal path. Record the expected reading before consulting the actual reading. This makes the diagnosis falsifiable. The best answer is not always a definitive fault name. Sometimes it is the most economical next measurement that separates two explanations.

18. Examination writing: show the mechanism, not a slogan

A one-mark definition may need a brief phrase, but an explanation question needs a causal chain. “The bulbs are dim because the current is low” may be incomplete if the question asks why adding another series resistor changes the circuit. Explain that total resistance increases at unchanged source voltage, so current decreases under the stated ideal conditions; the lamp’s power changes accordingly. When the question is about parallel branches, do not borrow the series story. Use because, therefore and hence to connect equations with physics. Write relevant units with numerical answers, and do a physical reasonableness check. Where a question asks “suggest”, a carefully supported possibility is better than a categorical assertion unsupported by evidence.

19. A revision route from the previous volumes

This chapter follows the sports-day Physics motion trial in Volume 1399, the timing calculations in Volume 1400, oral evidence in Volume 1401 and the integrated audit in Volume 1402. Those earlier guides showed how one event can produce different kinds of evidence. The new task moves from timing a person to diagnosing a modelled electrical display. For students crossing over from primary school, the PSLE Mathematics error-diagnosis guide trains the habit of distinguishing a modelling mistake from an arithmetic slip. The school’s actual laboratory instructions always take priority over a web learning exercise. In this series, “EMS” is a study grouping only. Individual SEC subject syllabuses determine what is examined.

Worked practice: apply the ideas to fresh data

Every question below is an original, hypothetical learning exercise. Work it before reading the explanation. The objective is to name the principle, show the necessary calculation and explain what the answer does not establish. A correct number without a reason is an incomplete habit.

Practice 1: Charge and time

A model circuit transfers 18 C past a marked point in 6 s. Find the average current. Answer: I = Q/t = 18/6 = 3.0 A. Show the equation first and the unit last. If the time doubles for the same charge, the average current halves. This is a test of interpreting a rate, not evidence that a particular scoreboard battery will work for a specified period. An incorrect answer of 108 A usually comes from multiplying quantities that should be divided. Make a habit of checking dimensions before computing.

Practice 2: Resistance calculation

A resistor has 4.5 V across it and 0.15 A through it. Find resistance. Answer: R = 4.5/0.15 = 30 ohms. The division is sensible because the unit volt per ampere defines an ohm. If the question instead supplies 30 ohms and 0.15 A, find V = IR = 4.5 V. Notice that changing the unknown changes the rearrangement, not the physics. When you see two pairs of readings, first decide whether the device can be treated as an ohmic resistor under the conditions.

Practice 3: Series verification

Two ideal resistors, 5 ohms and 15 ohms, are in series with an ideal 10 V supply. Calculate current and each voltage drop. Total resistance = 20 ohms, current = 10/20 = 0.5 A. The drops are 2.5 V and 7.5 V, adding to 10 V. If a student obtains 10 V across each resistor, the mistake is a parallel-circuit assumption. A complete response states that series current is common to both components and gives the numerical check. Do not use the word “shared equally”: they receive different potential differences because their resistances differ.

Practice 4: Parallel verification

In an ideal model a 4-ohm resistor and a 12-ohm resistor are connected across a 12 V source. Their branch currents are 3 A and 1 A; the source current is 4 A. The effective resistance is 12/4 = 3 ohms. Explain why the equivalent resistance is not 16 ohms. The branches give charge two routes; adding another conductive branch reduces the network resistance. The short computation is less important than recognising that both branches receive the full source potential difference. This pattern will recur in unfamiliar-looking circuits.

Practice 5: Two measurements, one contradiction

A worksheet claims a series circuit carries 0.30 A before a resistor and 0.10 A immediately after it in steady state, with no branches. Do not try to reconcile the numbers by saying current was consumed. The claim conflicts with the series-current rule. State a possible issue with the measurement, reading or worksheet labels; then propose checking instrument placement and repeating the readings. A strong answer distinguishes observed numbers from the assumptions used to explain them. It does not alter the data to force agreement with theory. Contradictions are clues about the method.

Practice 6: The branch that went dark

A fictional two-branch scoreboard has a working left indicator and a dark right indicator. Both are drawn in parallel. Give two possible local faults and one useful test. A broken connection in the right branch or a failed right-hand component are possibilities. Check a permitted reading across the branch or inspect the supplied circuit model to distinguish them. Avoid saying that the source is certainly flat, since one branch still works. The word “possible” is not a weakness; it accurately matches a limited observation. Your proposed test should lead to different predictions for competing hypotheses.

Practice 7: Voltage divider

An ideal 12 V source drives a 2-kilohm and 4-kilohm pair in series. Find the voltage across the 4-kilohm resistor. V = 12 × 4/(2 + 4) = 8 V. Across the 2-kilohm resistor, it is 4 V. Now sketch the output point again with the voltmeter across the other resistor; the reading changes without changing the source. This exercise builds the habit of describing exactly what was measured. The model assumes no significant loading by the voltmeter or any attached device. Those assumptions matter in a practical situation.

Practice 8: LDR placement

A two-resistor divider has a fixed resistor above an LDR and the output measured across the LDR. More light lowers the LDR resistance in the simplified model. The LDR then receives a smaller fraction of the supply voltage, so the measured output falls. If the output were measured across the fixed resistor, the direction would reverse. Describe the chain explicitly: light increases, LDR resistance decreases, voltage share changes. A student who writes “LDR voltage always rises in light” has missed the circuit arrangement. No numerical specification of an actual sensor is needed.

Practice 9: Thermistor placement

An NTC thermistor is connected above a fixed resistor in a potential divider, and output is measured across the fixed resistor. In the ideal model, a rise in temperature reduces thermistor resistance. The fixed resistor then takes a larger share of the supply potential difference; the output rises. Test the reversed arrangement: if output is across the thermistor itself, the trend reverses. Sketch each circuit before deciding. Never identify an actual overheating fault from this relationship alone, because the model has not supplied calibration or environmental measurements.

Practice 10: Current–voltage graph

A metallic resistor at constant temperature gives the model pairs (V, I): (1 V, 0.1 A), (2 V, 0.2 A), (3 V, 0.3 A). Describe the pattern and calculate R. Current is proportional to potential difference for these values, and R = 1/0.1 = 10 ohms. If current is plotted vertically, gradient = 0.1 A/V; its reciprocal is 10 ohms. An answer that states gradient = 10 ohms has confused the chosen axes. Under a changed temperature or device type, linearity is not automatically established.

Practice 11: Power and duration

A fictional display segment takes 0.25 A at 8 V for 3 minutes, treated as constant. Calculate power and energy. P = 8 × 0.25 = 2 W. Convert three minutes to 180 s, then E = Pt = 360 J. The common error is using 3 directly as seconds. Another is calling 360 W the energy. The complete solution states the ideal constant-voltage and current assumption. The numerical result is a classroom model, not a battery-life or safety prediction. Units reveal many mistakes before the final sentence does.

Practice 12: Interpret a surprising reading

Three repeated source-current readings are 0.21 A, 0.20 A and 0.35 A for the same claimed setup. Should the student delete 0.35 A? No. Record it, check that each reading was taken at the same location and under the same settings, inspect whether the connection was changed, and repeat appropriately. A single anomalous value may indicate measurement error or a real change. Calling it a mistake without examining the method is not evaluation. The revised report should show what was investigated and which conclusions remain reasonable. In practical science, transparent anomalies are more useful than invisible ones.

Practice 13: The misleading announcement

A fictional committee drafts: “Our new scoreboard will never fail because two test indicators lit up.” Rewrite the claim. An appropriate version is: “In the classroom demonstration, two indicators operated during the observed trial; this does not establish long-term reliability.” The revision removes the absolute promise and identifies the limited evidence. Physics supplies the measured behaviour; English supplies clear distinctions between fact, inference and overstatement. This is an original communication exercise, not a real school notice. The transfer skill is resisting a conclusion that claims more than the data can show.

Practice 14: A structured-response chain

Question: Explain why adding another fixed resistor in series reduces current when an ideal source voltage remains constant. Model answer: The total resistance of the series circuit increases. Since I = V/R and source potential difference is unchanged, the circuit current decreases. To extend, describe how a suitable component’s energy transfer rate changes if the relevant current or potential difference changes. Do not say that the added resistor “steals current”; current is common along the series path. The examiner needs a physical mechanism, not a metaphor that contradicts it.

Practice 15: Practical planning

Plan a supervised low-voltage investigation of how current varies with potential difference across a resistor. Identify potential difference as independent, current as dependent, and resistor identity and approximate temperature as controls. Place the ammeter in series and the voltmeter in parallel with the resistor. Collect several pairs of readings, repeat where practical, plot an appropriately labelled graph and describe its trend. State a safety precaution relevant to the approved apparatus and equipment ratings. A vague answer such as “be careful” is not a method. Also explain what would count as evidence against your hypothesised relationship.

Practice 16: Comparative diagnosis

Two proposed explanations remain after a dark indicator is observed: H1 says the branch is open, while H2 says the supply itself is absent. Another branch stays lit. Which hypothesis is better supported? H2 conflicts with the independent working branch under the stated ideal common-source arrangement, so a local branch issue has stronger support. That still does not distinguish a wire failure from a failed indicator. Name the additional observation needed. This layered argument, from eliminating one possibility to retaining several others, is central to data-based Physics questions. Certainty should increase only when evidence increases.

Going further 1: Turn a calculation into a complete exam response

Many students obtain correct arithmetic yet lose clarity by omitting the physical principle. Write a line naming the arrangement, a line with the relevant rule, a line substituting values with units and a final line interpreting the answer. For the two-resistor series example, “Series resistances add: 5 + 15 = 20 ohms; I = 10/20 = 0.50 A; the same current passes through each resistor.” Compare this with “0.5” alone. The longer answer is not busywork: it allows another reader to reconstruct your reasoning and catches hidden assumptions before they become marks lost. For descriptive responses, the equivalent structure is observation, scientific relationship, explanation and limitation.

Going further 2: What to do when a diagram is deliberately unfamiliar

Draw a simple boundary around each component branch and find junctions before applying an equation. Trace a possible complete path from one terminal of the source through components and back. Ask whether two resistors are genuinely in series; if a branch separates between them, adding them directly may be wrong. Ask whether two resistors really share the same two endpoints before calling them parallel. These are structural questions, not visual guesses. A neat diagram can be redrawn with the same connectivity in a different shape and the physics remains the same. Practise redrawing a circuit in a cleaner arrangement while preserving every connection.

Going further 3: Why a higher reading does not always mean improvement

Suppose an intended display branch shows an increased current after a connection is changed. It is tempting to interpret larger current as a stronger or better scoreboard. The evidence alone does not establish that outcome. A higher current may reflect lower resistance, a changed voltage or an unintended path. The proper question is what the measurement was meant to indicate. Read the design assumptions, compare the current with the intended operating model and identify missing information. Because this is an educational low-voltage scenario, do not infer that a real component can safely carry the value shown. In examination answers, words such as “therefore better” require a defined criterion rather than enthusiasm for a large number.

Going further 4: Test proportionality at more than two points

Two points alone can always be joined by a line, but a reliable physical pattern needs a sensible range of readings. With 1, 2, 3 and 4 volts across an ohmic model, proportional currents should lie near a straight line through the origin when temperature is controlled. If the fourth point bends away, consider whether the material warmed, the instrument was misread or the model is incomplete. Do not force every point onto an ideal line. Use several readings so the trend becomes visible. The assessment skill is not simply drawing; it is evaluating what the graph allows you to claim and where its conditions cease to hold.

Going further 5: A four-week progression that does not rely on memorisation

During the first week, learn the language of charge, current, energy transfer, resistance and voltage, and draw simple circuits until each symbol has a purpose. In the second week, solve series and parallel examples with unit checks, then explain in words why each calculation matches the topology. In the third, interpret I–V plots, potential dividers and sensor changes, using diagrams rather than memorised trends. In the fourth, attempt mixed evidence packs: a diagram, two measurements, one apparent contradiction and a requested conclusion. Keep an error log with three columns: wrong assumption, corrected principle and a new test question. Revision is complete only when a different diagram no longer defeats the same idea.

Going further 6: Parent and learner decisions about additional practice

More worksheets are useful only if they address the actual weakness. A student who cannot distinguish series from parallel will not gain much from a difficult numerical paper until the path structure is understood. A student who understands circuits but omits units may need brief daily answer-checking rather than extra teaching. A student who answers every “suggest” question with certainty needs evidence evaluation. Parents can ask the learner to explain one circuit aloud and identify the assumption behind each step. If a teacher or tutor is involved, share representative errors and recent school feedback, not just an overall mark. The objective is independent reasoning, not dependence on an adult to confirm every answer.

Going further 7: Mini-mock and self-marking protocol

Set aside twenty-five minutes for an original mini-mock: draw a circuit with two ideal parallel resistors of 6 and 12 ohms on a 6 V source; determine each branch current and source current; propose one reason a single indicator might fail while the other remains on; identify a useful test; then write a careful two-sentence public summary. Expected numerical answers are 1.0 A, 0.50 A and 1.50 A. Award yourself credit only when the relationship, working, units and limitation are present. Repeat the mini-mock after a day using different numbers. Successful learning should survive a changed surface story.

Final checkpoint

Make a clean one-page explanation of an unfamiliar circuit without notes. Include a diagram, a labelled numerical calculation, a predicted meter reading and a sentence that distinguishes measurement from inference. If you can do that, you are closer to independent examination performance than a learner who has memorised sixteen formula-looking answers without understanding a single path. Continue to the Mathematics scoreboard audit in Volume 1404 and then the English evidence-reading chapter before attempting the cross-subject review.

Read the earlier Physics Sports-Day motion guide (Vol 1399) and the EMS results audit (Vol 1402). For an earlier bridge, see PSLE Mathematics error diagnosis. For supervised Science learning decisions, the Sengkang Science learning support guide offers a parent-facing route.

Official syllabus references: 2027 G3 SEC subject list and G3 Physics K323 (accessed 17 November 2026). The official requirements, not this independent guide, govern the examinations.